coastalloha.blogg.se

Lg washing machine parts
Lg washing machine parts










  1. Lg washing machine parts how to#
  2. Lg washing machine parts code#

In rare cases, the replacement of the electronic controller is required. You have to change the burnt out triac and relay, which are responsible for the work of inlet valve and/or solder tracks. In 90% of cases, the control module is repairable. The washer does not gain water and shows the 1E error code.ĭefective control board (electronic controller), the microchip that controls the processes of the machine, is broken. If the clogging is not a reason of fault, you need to replace the pressure switch. Perhaps the pressure switch tube is littered. The pressure switch (the water level switch), which controls the amount of water in the washer, is broken. It is necessary to change the water supply valve. Buy MFG63099101 LG WASHER/DRYER COMBO DOOR LOCK HOOK online at a competitive price and have it delivered Australia wide from Statewide Appliance Spares. In rare cases when the valve is slightly opened, the machine does not gain enough water. It does not open by the signal of a control module, and water does not enter into the machine. The inlet valve, designed for supplying the washer with water, is broken. LG washer can’t cope with water gaining (in rare cases it gains too little water) and displays the IE error code. In the table below you can view the list of faults that may cause the 1E error of LG washer. Possible malfunctions, which require repair Perhaps there was a failure in a control unit.

  • Try to turn off the washer for 15-20 min and then turn it on again.
  • Remove and clean the filter mesh by placing it in a solution of citric acid for 1-2 hours. In this case, your LG washer gains little water and shows the 1E error code. The filter mesh prevents the machine from small particles contained in a tap water. It is located in the place where the inlet hose is connected to the washing machine. This hose is designed for supplying the machine with water.

    lg washing machine parts

    It is possible that a water inlet hose is twisted or pressed down.Weak water pressure in the water supply system could also cause the fault: LG washer can’t cope with gaining of water in time.Therefore, always open the shut-off valve fully.

    Lg washing machine parts code#

    In this case, the washer gains water longer than usual, and then displays the 1E error code and does not work. Sometimes a stopcock is not closed fully.Perhaps you forgot to open it before washing. Check the shut-off valve which blocks the water supply to a washing machine.

    lg washing machine parts

    It is necessary to restore the water supply.

    Lg washing machine parts how to#

    APO/FPO, Afghanistan, Alaska/Hawaii, Anguilla, Antigua and Barbuda, Armenia, Aruba, Bahamas, Bangladesh, Barbados, Belize, Bhutan, Botswana, British Virgin Islands, Brunei Darussalam, Cayman Islands, China, Costa Rica, Dominica, Dominican Republic, El Salvador, Fiji, Finland, Grenada, Guadeloupe, Guam, Guatemala, Haiti, Honduras, Hong Kong, Indonesia, Jamaica, Kazakhstan, Kiribati, Kuwait, Kyrgyzstan, Laos, Maldives, Marshall Islands, Martinique, Mexico, Micronesia, Moldova, Montenegro, Montserrat, Nauru, Nepal, Netherlands Antilles, Nicaragua, Niue, Pakistan, Panama, Papua New Guinea, Russian Federation, Saint Kitts-Nevis, Saint Lucia, Saint Pierre and Miquelon, Saint Vincent and the Grenadines, San Marino, Saudi Arabia, Solomon Islands, South Africa, South America, Svalbard and Jan Mayen, Taiwan, Tajikistan, Thailand, Togo, Tonga, Trinidad and Tobago, Turkmenistan, Turks and Caicos Islands, Tuvalu, US Protectorates, Ukraine, Uzbekistan, Vanuatu, Virgin Islands (U.S.The IE (1E) error of LG washer: what to do and how to repair the machine by your own?












    Lg washing machine parts